3/16/2024 0 Comments Logitech harmony remote software 7I find it interesting that the latest Windows 7 version is 7.7.0, while on the Mac, it is 7.8.0, or 7.8.1, depending on which Mac OS is in use.Īny comments or experiences? My last notes & e-mails to Logitech have gone unanswered. I'm not trying the Windows side, for fear of it happening to them also. So, I can't do anything now on either Mac, with the software. It seems like a virus or bug that has infected both computers and emanates from Logitech's web-software. I haven't the spirit to un-install, and update to a later software version downstairs, due to the history. most interestingly, my downstairs Mac (7.7.0), also now only opens to a blank window. now, my IMac upstairs will only open Harmony ONE software to a blank window(this after MANY un-installes, re-installs, re-downloading and re-installing, etc, of the latest software versions). I connected my Harmony One, updated it and all was well, since now, with the updated database, the software didn't need to try to read my IR/RF Comcast remote anymore. By then the software knew of my MAC settings, and had even updated itself with an addition to its database, renaming my set-top Box as a PVR. I went back upstairs, restarted my Mac in the 'dark side' mode (Windows 7- Bootcamp), downloaded the Logitech Harmony One software (7.7.0), and it opened and worked OK. So, I went down to my workshop older Mac laptop(running 7.7.0), and proceeded about my business, including writing a note to Logitech about my troubles[ IR/RF, AND the software not loading). When I installed it, I got the same blank window, and have been unable to do anything about it. It occurred to me that I might need a software update so I downloaded 7.8.1 to replace the 7.7.0 I had been using on my almost brand-new IMac. Then the regular widow loaded, and I proceeded with my IR/RF problems. When I re-opened it, all that showed up was a blank window( after a (at the window's bottom) web-based update) which remained blank for about 10-15 minutes. However, after trying to update the Harmony remote with the supplied Comcast remote(unsuccessfully, because the remote was only putting out RF), I quit the program, which had opened very slowly(unusual). This software has always worked well and faithfully. In the process, I updated my Harmony One, and in THAT process, I opened and tried to update the remotes with my computer's Logitech software. There were several problems, centered upon when the supplied remotes were using RF, versus IR(which is required by the Harmony One). NOTE: It is recommended to perform these steps for all Activities that use the television.A few days ago, I had to update my home entertainment system with two new HD Comcast set-top boxes, which use IR/RF signals to change channels and decode the newly encrypted basic service. Once finished, click on the (Next) button TV need to be on? From the list, select the input that the TV uses for this Activity. Click on the Next button through the Activity setup screens until you arrive at the screen asking the question "What input or channel does your.Select No, I want to run the setup wizard again to change these settings and click on the (Next) button Confirm the input chosen for your television is correct.Select Review the settings for this Activity and click on the (Next) button.Click on the (Settings) button for the Activity you wish to troubleshoot.Click on the (Activities) tab on your home page.Why UpdateConfigure your Harmony remote so it can. Launch the Logitech Harmony Remote software and login to your account Logitech Harmony Remote Software Logitech Support + Download Welcome to Logitech Support Logitech Harmony Remote Software Set up and configure your legacy Harmony remote.If this has not fixed the problem, proceed to the next section Confirming your Activity Settings Please try switching between your other Activities to see if they switch correctly. Your television was simply out of synchronization with your Harmony remote and should now work correctly. ![]() If you now have a picture on your TV screen, answer Yes when asked if the problem is now fixed.If the TV switches to another input but no picture is seen, continue answering No until an image appears In this example HDMI 1 is used, though this may vary from your setup. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |